- MECO LED BADGE DEVICE DRIVER SERIAL
- MECO LED BADGE DEVICE DRIVER DRIVER
- MECO LED BADGE DEVICE DRIVER PRO
Unlike the other C64-compatible systems, the SX64 uses a ribbon cable to connect the top loading expansion port with the main system PCB. Normally, all switches can be left in the “on” positionIO1/IO2 swap jumpers must be moved as a pairWhile the X-Pander 3 will work with the SX64, its use is discouraged. Also, since the “bus” places additional load on the unbuffered expansion port IO lines, cartridges that are susceptible to signal degradation may not work with X-Pander 3, even when installed alone.Some helpful hints:Always insert or remove X-Pander 3 with the system port offClean cartridge contacts before installationSwitches are “on” when depressed. Thus, it is impossible to detail the nearly infinite combinations and whether each works or not. Our thanks to Carsten Jensen for creating the X-Pander3 User’s Manual.Expansion port cartridges were not normally designed to coexist with other cartridges. Jumpers are provided, but the jumper pins can be removed and replaced with a subminiature DPDT (double pole, doub e throw) switch.SupportThe unit works exactly like the Creative Micro Designs EX3 (EX2+1) units, so instructions for those units will work equally well with the X-Pander3.
MECO LED BADGE DEVICE DRIVER SERIAL
This can be used to move a peripheral cartridge (like a serial card or ethernet card) normally residing at IO2 to the alternative IO1 position so that it can coexist with the RAM Expansion Unit, which must reside in IO2. The X-Pander 3 offers the following features:3 individually-selectable expansion portspower indicators for each portAbility to swap IO select lines on 2nd and 3rd portseasily accessed piano-style configuration switchestop-loading or back-loading 3rd port.3rd port can accommodate 2 cartridges at the same time*reset switch* Both top and back-loading options for port 3 share a single set of configuration switches, requiring 2 cartridges that can coexist without configuration.RequirementsCommodore C64, C64C, C128, C128D, or SX64Technical DetailsX-Pander 3 creates a “passive” cartridge port “bus”, with switches on the following lines:Power (2 switches)IO1 ($de00-$deff)IO2 ($df00-$dfff)ROML ($8000)ROMH ($a000)EXROMGAMEAdditionally, ports 2 and 3 contain jumpers allowing one to “swap” IO1 and IO2. Utilize multiple cartridges at once, or easily switch cartridges without removal. Github link: heir-apparent to the CMD EX-3 and EX2+1, the X-Pander 3 opens up a wealth of expansion options for your Commodore 64, SX64, C128, or C128D.
MECO LED BADGE DEVICE DRIVER PRO
Playstation PS2 Dualshock to DB9 (DSUB 9) Adapter for Commodore, Amiga and Atari Computers Use Arduino pro mini to connect your Playstation 2 Dualshock to your retro computers.Amiga 500 Kickstart EPROM Adapter for Rev 5 Boards You can use your burned EPROM chips (27C40) with your Amiga 500 Rev5 boards.Bill of Mater.GVP-Compatible 64-Pin 4MB SIMM GVP-Compatible 64-Pin 4MB SIMM PCB for GVP Accelerator Cards,Made by: Tube TimePlease check the site.Check project documentation for details and BO. Dennis RGB to HDMI Adapter for Amiga 500 with Raspberry Pi Zero A Dennis chip adapter to give your Amiga HDMI output.DRAM Test Shield for Arduino Uno and Nano This project is tested and works okay!To use it with Arduino Uno, solder male pin headers on the bot.Playstation 2 Dualshock to DB9 Adapter Board (Double Connector) This project is tested and runs okay :)This version is only for C64This board is an extended version.6502 (W65C02S) to Atari SALLY adapter Board This project has been developped by TheByteAttic, Thanks for this awesome project,Check his youtube.KungFuFlash Cartridge for Commodore 64 This is a project by Kim JorgensenDetails can be found on his github page.SwinSID Micro SwinSID is a microcontroller based clone of the SID, the audio chip used in nearly all 8-bit Commodo.
MECO LED BADGE DEVICE DRIVER DRIVER
MAX7219 Driver Board for 7 Segment Display This is a tested and working project.Use this board to easily integrate 7 segment displays in your p.Power Distribution Board (PDB) for Drones This is a basic Power Distribution Board for Drones (Quadcopters)You can use it as a bare PCB to con.